Olympia Chimney Chimney Liner & Rebuild Nationwide

Olympia Chimney Chimney Liner & Rebuild in Jamaica: What to Know First

An Olympia Chimney liner replacement or rebuild in Jamaica typically runs $2,400 to $6,800 depending on liner type, flue height, and whether the masonry crown and top courses need rebuilding at the same time. Most jobs take one full day; a full tear-down and rebuild runs three to five days. Every quote is written before work starts, with the price, scope, and warranty on paper, not described over the phone.

Call (516) 240-9612

If you own a home in Jamaica and your Olympia Chimney liner is spalling, rusting through, or the crown looks like a jigsaw puzzle after last winter’s freeze-thaw cycles, this page is for you. Call (516) 240-9612 and we’ll schedule a camera scan, write up what we find, and hand you a number.

How Olympia Chimney Products Fail - and How We Fix Them

• Olympia Chimney’s 316L flexible liner (the most common liner we see in Jamaica row houses and attached homes): the seam welds tend to pit where creosote sits longest, usually in the lower third of the flue above the appliance outlet. Pitting turns into pinholes, and pinholes let exhaust into the chase or the wall cavity. The fix is a full liner replacement, not a patch. We pull the old liner, camera the chase, and size the new one to the appliance’s actual BTU output, not the old liner’s diameter.
• Olympia’s rigid oval liner in older masonry chases: oval liners get installed where the flue is too narrow for round, and we see the longer flat sides bow inward over time, especially in chases that run up the unheated exterior walls of Jamaica’s pre-war housing stock. Bowed walls catch creosote faster and make a liner un-cleanable. We replace with the correct oval-to-round ratio or open the chase if the masonry allows it.
• Liner-to-connector fail points at the appliance outlet: this is the joint we see leaking on Olympia Chimney installations more than any other brand, because the connector pipe was sized by whoever installed the stove, not by the flue manufacturer. The gap gets sealed with foil tape or furnace cement, and both fail. We cut the connector back, rebuild the joint with the correct adapter, and lock it with three stainless screws, not tape.
• Top-plate and rain-cap corrosion at the chimneytop in Jamaica’s salt-air and heavy-rain climate: Olympia’s standard galvanized top plates will rot right at the bolt holes, usually within eight to ten years near the Cross Bay corridor. We replace with stainless top plates and caps, and we bed them in high-temp silicone so the bolts aren’t the only thing keeping water out.
• The “seller’s disclosure” liner: we see a lot of Jamaica homes sold between 2018 and 2023 where the disclosure says the flue was lined in the last five years, and the camera shows an Olympia liner that was clearly a DIY kit install. Missing insulation wrap, no support at the offset, and a liner that terminates three feet short of the crown. The fix isn’t always a full replacement; sometimes it’s correcting the installation. The camera tells us which one.

Our Olympia Chimney Chimney Liner & Rebuild Process

1. 1
   Camera first, always. We run an NFPA 211 Level 2 scan down the entire flue, top to appliance outlet. You see the footage while it’s live. If the liner is shot, you’ll see the holes and the delamination yourself, on the spot. The camera doesn’t negotiate, it just shows what’s there.
2. 2
   Written findings and a written price. Before anyone touches a tool, we write down what the scan showed, what we recommend, what it costs, and what the warranty covers. Clause 1 of the Haven Standard: have it in writing.
3. 3
   Parts decision: OEM Olympia Chimney parts or equivalent aftermarket. For most liner replacements, we use DuraFlex or Copperfield stainless liners sized to spec, because they’re often a better value and hold up as well or better in Jamaica’s climate. If the job calls for an Olympia-specific component (a particular top-plate pattern or an odd oval dimension), we source the OEM part. We tell you which is which and why.
4. 4
   The work, with a named tech. You get a text when the tech is on the way, and you know who’s showing up. The flue gets cleaned down to bare masonry before the new liner goes in, because putting a new liner over old creosote is throwing money away.
5. 5
   Photo record on completion. Clause 4 of the Haven Standard requires a documented photo record on every job. You’ll see the installed liner, the crown work, the cap, and the connector joint. If there’s a masonry rebuild component, you’ll get photos of the mortar joints and the crown form before and after.
6. 6
   Warranty and the 365-Day Done Right Promise. Every job carries a written warranty. If it’s not done right, we make it right. That’s stamped on the paperwork.

Before

After

What Olympia Chimney Chimney Liner & Rebuild Costs in Jamaica

A straight Olympia Chimney liner replacement in a typical Jamaica flue, 20 to 25 feet, runs $2,400 to $3,800 for 316L stainless with a new top plate and cap. An oval liner conversion runs $3,200 to $4,600. A partial rebuild (top eight to ten courses and a new crown, with liner replacement) runs $4,200 to $6,800. A full tear-down and rebuild from the roofline up starts around $7,500 and tops out near $12,000 for tall three-story Jamaica row houses with difficult roof access.

What moves the price: flue height, oval versus round, whether the old liner comes out in one piece or has to be cut out in sections, roof pitch and access, and the condition of the masonry crown once we get eyes on it. Estimates are free and written. Call (516) 240-9612.

Why Jamaica Homeowners Call Level Two Chimney Jamaica for Olympia Chimney Work

Corrine Halstead has been running chimney inspections and cleanings across Jamaica for the better part of two decades, including the older row houses near Jamaica Avenue where the flue work is rarely what the seller’s disclosure says it is. When our techs open up an Olympia Chimney chase, they know what they’re looking at, and they know which failures are liner failures and which are installation failures.

We stock and source DuraFlex, HeatShield, and Gelco components as alternates when they’re the better call, so you’re never boxed into one manufacturer’s parts price. We document everything. We answer the phone live, 24/7. And if you bring us a competitor’s written estimate, we’ll give you a free second opinion on it, line by line. Written price before work starts, photo record when it’s done, and a follow-through guarantee that most contractors won’t put on paper at all.

FAQs